Simple Slide Panel
 
 

Step by step Invisible Phone Guard (IPG™) installation instructions:

For best results, please take some time to read the instructions before you install your IPG. The installation is simple, and the results are beautiful!

BEFORE YOU BEGIN: Wash hands

OFF:The divice must be TURNED OFF

CLEAN: Wipe the device with soft dry cloth

PREPARING APPLICATION SOLITION: Prepare mixture of water and small amount of dishwashing detergent (2-3 drops).  And mix it.

PEEL:Peel the IPG™ from backing (While fingers are WET)

WET: Buraya ne gelecek

APPLY: Align IPG™ to device, (adhesive side down) to apply

SQUEEGEE: push the excess moisture and any bubbles away from the center towards the edges, and away from any open or uncovered ports

WAIT:If looks foggy do not panic. Let it dry 12 to 24 hours. Micro-bubbles and imperfections will work themselves out in two to three days.

Don’t forget to:  Use your palm for the corners. Hold the device in your palm for 1-2 minutes





 HELPFUL TIPS: For challenging tabs and flaps that wrap around the sides or over corners, we recommend first holding the tab or flap in place against the device using your palm (or thumb, for small pieces) until it is secure.
Once it feels secure, use a blow dryer on a LOW, COOL setting to dry the pieces into place.
Ensure the small parts are as dry as possible before applying them. If they get too moist, let them dry for a few minutes before placing them on your device. This will make them tackier and easier to position correctly.

We recommend letting your device sit overnight before turning it back on (12-24 hours is suggested). This will give the IPG™ time to "set" properly, and allow any remaining water solution on your device to fully dry.

Special Installation Tips

Palming

Our installers use a technique for securing problematic corners and edges called "palming." Begin by aligning the IPG in the correct position and removing as much of the excess moisture as possible. Then, apply pressure to the tabs and flaps by holding them against the palm of your hand for 30 seconds to 1 minute. This process may need to be repeated several times, but will help secure difficult pieces.

Use your palm to corners. Hold the device in your palm 1-2 minutes

Cleanliness
For the best possible results, wash your hands before beginning and perform the installation in a clean area. Make sure your device is clean and free of skin oils.

Alignment
Alignment is one of the most important aspects to your IPG™   looking "perfect" once it is on the device, and we recommend checking where each piece goes prior to installation. Please check the product pages on our website, as many of our full body designs have coverage information for each individual design. If the IPG™ has multiple holes for buttons, we recommend aligning to the top first, then the sides, and finally the bottom. Check the overall alignment as carefully as possible prior to using the squeegee.

Use of a lamp
Using a lamp as a very low source of heat can help speed up the installation process, particularly for some of the more complex IPG™   designs. A lamp with an extendable arm, such as an office lamp, can be used to slightly heat the IPG and help it to adhere. WE DO NOT RECOMMEND LEAVING YOUR DEVICE UNDER HEAT FOR ANY EXTENDED PERIOD OF TIME, WHICH COULD DAMAGE THE ELECTRONICS.

Blow Dryer
A blow dryer is also very useful for corners, tabs, and edges when installing the IPG™. The best method is to put the blow dryer on the lowest and coolest setting, and use a side-to-side sweeping motion to dry the piece or section. If the blow dryer is on a warm or hot setting it can slightly warp the IPG™. If this does happen, discontinue using the blow dryer and the IPG™   should return to the proper shape in 10 to 15 minutes.

Installation Order
Installing the back piece(s) of a full body IPG first can be helpful if you have not done it before. Installation flaws on the back of a device may not be as significant or noticeable as they would on the screen, so you can use it as practice, or to better understand the installation process.

Back

 
Company Info Customer Support FAQ Video Gallery Register Your Product
Become A Reseller Contact Popular Devices Aerospace Grade Open A Mall Cart
Return Policy
 
Privacy Policy